|
X-10 Transmitter Interface - HAM-001
Let your InControl system communicate with a wide range of X-10 home automation interfaces with the X-10 transmitter interface. Connecting between the automation interface on the back of the InControl transmitter unit and any spare mains socket, the X-10 transmitter interface is all you need to get your automated home started.
Price: £42.00
|
|
|
|
X-10 Appliance Module - HAM-002
By far the simplest method of automating an electrical device is to use on of these X-10 appliance modules. Simply give the module a unique address and plug it into a mains socket and any device then connected to the module can be controlled by your InControl system. Capable of handling a load up to 13 amps, the appliance module is perfect for controlling dish washers, kettles, radios and more.
Price: £20.00
|
|
|
|
|
X-10 Lamp Module - HAM-003
Like the X-10 appliance module, installing the X-10 lamp module is a breeze - just connect it between the lamp you wish to control and the mains supply and you've instantly got a light that can be switched on and off, and even dimmed directly by your InControl system. Capable of controlling lights rated between 60W and 300W, the X-10 lamp module is just the thing for adding computer-controlled ambiance to your home!
Price: £20.00
|
|
|
|
X-10 Light Wall Switch - HAM-004
The X-10 wall light switch is a direct replacement for the wall light switches within your home. Simply set the switch's address and then wire it into the existing light fitting and you've instantly got an automated light switch! Offers both on and off control and full dim facility. Note that it should only be used for incandescent lights rated between 60W and 300W. Can also be manually operated like a normal fader light switch. For fluorescent and 'energy saving' bulbs, use the X-10 appliance wall switch instead.
Price: £25.50
|
|
|
|
X-10 Appliance Wall Switch - HAM-005
The X-10 wall appliance switch can control any type of electrical load ranging from 10 amp resistive, up to 2000W incandescent and 3 amp motor. Ideally suited to control any electrical device that is wired directly and controlled via a wall plate switch (such as a heater or water boiler, for example). Features a small red LED that illuminates when the switched is activated. Note that a neutral connection is required for the installation of this switch. Can also be manually operated like a normal appliance switch.
Price: £25.50
|
|
|
|
X-10 Infrared Adaptor - HAM-006
If you've got a programmable universal remote controller like the Philips Pronto or Marantz RC5000i then this little gadget is all you need to get your controller talking to your X-10 equipment. Simply plug it in, 'teach' your remote the appropriete codes and you'll be controlling upto sixteen X-10 devices on a specified house code from the comfort of your armchair! The adaptor also includes manual X-10 controls which provide a quick and easy way of controlling X-10 automated devices when you're not near your InControl system.
PLEASE NOTE - Works with most Universal Remote Controllers - please check compatibility of your remote with manufacturer before purchasing.
Price: £32.10
|
|
|
|
X-10 Universal Relay Module - HAM-007
The X-10 universal relay module lets you control devices that require contact closure switching such as garage doors, motorised screens, curtain openers and more. The module features both momentary and continuous switching (selectable) of a maximum 24 volt 5 amp input. In addition, the module features a unique sounder which provides an audible beep when the module is activated. The module can be set to activate the sounder independantly or in conjunction with the relay via a switch on the unit.
Price: £28.49
|
|
|
|
X-10 RF Receiver - HAM-008
Used in conjunction with the X-10 RF Handset (below), the X-10 RF Receiver module provides a quick and simple way of manually controlling your X-10 automated devices. Simply plug the RF Receiver unit into a wall socket and use the RF handset (not supplied) to switch devices on and off from anywhere within the home. The RF Receiver operates on a frequency of 433MHz and also includes a built in appliance module (set to device 1 on a selectable house code) with a manual on/off button.
PLEASE NOTE - Requires X-10 RF handset (below) to work
Price: £29.70
|
|
|
|
X-10 RF Handset - HAM-009
Used in conjunction with the X-10 RF Receiver (above), the X-10 RF Handset provides a quick and simple way of manually controlling your X-10 automated devices. Similar in design to a conventional television remote control, the X-10 handset features a bank of eight on and off push buttons and a pair of dim/brighten buttons. With a selectable 'hi/low' bank switch and a house code control, the handset can be configured to control X-10 devices 1-8 or 9-16 on a specified house code.
PLEASE NOTE - Requires X-10 RF Receiver (above) to work.
Price: £23.80
|
|
|
|
X-10 Mains Filter - HAM-010
Although it is very unusual, some appliances (refrigerators and some older televisions, for example) can interfere with the operation of X-10 by introducing 'noise' onto the mains supply. To get around this problem, we offer the X-10 Mains Filter which - as it's name suggests - filters out noise before it gets onto the mains supply. Simply connect the mains filter between the power socket and the offending appliance.
PLEASE NOTE - If you are encountering problems with powerline noise, we advise you to call our technical support team before ordering this item.
Price: £29.30
|
|
|
|
X-10 Starter Kit - BUN-001
Start off your X-10 fun with this starter kit which includes the transmitter interface, 1 appliance module and 1 lamp module.
Price: £80.85
|
|
